Wipe up slips or spills before they have a chance to set on your shell surfaces. We recommend avoiding harsh cleaners with ammonia or abrasive chemicals. Just make sure the shell mosaic has grout lines to reduce slipping.Ī: These shell tiles are best cleaned with light soap and water. You can use them for shower walls, or even slip-resistant shower floors. Q: Where can I install Mother of Pearl Tiles?Ī: We recommend installing shell tiles, either on their own and in marble mosaics, in indoor locations only! They're a beautiful option for interior walls to create a glamorous accent wall or luxurious backsplash. We suggest placing rugs at entrances to minimize dirt and grit from being tracked into the tile flooring from outdoors.Tile Club is the best place to buy Mother of Pearl tiles online! We are in love with the stunning sheen of Mother of Pearl tiles! These beautiful shell tile designs add a luminous glow to give your home a luxurious finish! The iridescent shine of shell is a beautiful addition to any interior, with a reflective quality that increases natural light! Frequently Asked Questions about Mother of Pearl Tile:.Leftover steel particles may create rust stains in the grout. Avoid using agents that contain any dyes or colors.Do not use wax, oil-based, abrasive cleaners, or sealants.Do not clean porcelain tile flooring with ammonia or cleaners that contain bleach and/or acid, as this may modify the grout color.Rinse the floor with clean, clear water to remove the cleaning solution.įor high traffic locations, we suggest cleaning the floor at least once per day and wet mop at regular intervals.Scrub the floor with a brush using the two-direction method. ![]() ![]() Allow the cleaning solution to remain on the floor 5–10 minutes. Next, saturate the tile with a neutral cleaning solution such as vinegar and hot water and stir.This effectively dislodges dust and debris from inside the textured surface. When sweeping, use a soft-bristle broom and sweep in two directions: first, sweep along the direction of the grain in the tile.Sweep or vacuum dust and debris from the floor.Porcelain tile, while impervious, may still have its surface subject to discoloration if not cared for properly. We suggest a solution of 1/4 cup of white vinegar to every 2 gallons of water. Porcelain tile is one of the easiest flooring materials to clean. We highly recommend applying grout release prior to grouting the tile to facilitate cleaning and for protection against staining from contrasting color grouts.įor the best results, use a wet-saw with a new, continuous rim diamond blade designed to cut ceramic tile.Use a damp sponge for the final cleaning and to smooth out the grout joints.Before grouting, test an area to make sure the stone surface will not scratch.For all-ceramic tiles, we suggest using non-sanded grout in order to prevent scratching.When installing our ceramic material, use a 3/16" or 1/4" square notch trowel.We suggest using a 9" Trowel with a 1/8" square notch.Prior to fixing the tiles in the mortar bed, use the flat side of the trowel to smooth down the ridges.Grout joint should be a minimum of 1/16” and not butt set.Apply as much adhesive as can be covered within 10-15 minutes.For faster installation, use a rapid curing thin-set mortar. ![]() To avoid affecting the color of the tile, we highly recommend using white thin-set mortar. This will also help you plan out the placement of the pieces, which is especially helpful with tiles that have a lot of variation. Make sure that you practice laying out the pattern. Think about the cuts in advance and visualize the installation. We recommend that you dry-fit your pattern first. In all corner joints, install using silicone caulking sealant instead of grout. ![]() Expansion joints should be installed at all changes in plane in the tile work and where tile abuts restraining surfaces. See manufacturer's recommendation for a waterproofing and crack prevention membrane that is compatible with the setting material you are using. If used in a wet area, it is essential to waterproof. Tile should be installed over a clean flat surface that is free of contaminants, including curing compounds. To ensure a proper installation, the tile must be installed over a suitable substrate. We cannot make any adjustments or provide service after the installation has begun. Before you begin installation, please inspect the goods for any damage or defects such as chipped edges or broken pieces. There will be naturally occurring variations in the color, pattern, texture, and veining that may differ from what was pictured.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |